Showing all 68 results
-
-
CO2 Cage Parts & Accessories (1)
-
DrainDroyd Parts & Accessories (13)
-
Extractor Parts & Accessories (39)
-
fracTron Parts & Accessories (1)
-
MPCart Parts & Accessories (2)
-
pure99 Parts & Accessories (1)
-
terpTRAP Parts & Accessories (2)
-
1-1/8″ Wrench | #50-0083
$41.00Used for tightening/loosening CGA 320 fittings located on the CO2 Cage manifold.
-
-
-
110 Extractor Kit | #10-1006
$900.00Items included:
Spanner Wrench
O-Ring Removal Tool
3/8″ Square Drive Socket
1-1/8″ Wrench
1-3/4″ Wrench
2-1/2″ Wrench
Flat Tip Socket Driver
5L Extractor Bags (Set of 2)
3″ Extractor O-Rings (Pack of 25)
Food Grade Anti-Seize
1.5″ Wire Mesh Disc
1.5″ Internal Retaining Ring
3″ Peroxide Cured O-Ring -
-
-
-
-
Back Pressure Regulator, 10K PSI | #80-0003
$1,575.0010K PSI BPR used in extraktLAB’s E-110, E-140, E-180 & pure99.
-
Bag Lifter | #90-1235
$3,600.00This is an UPGRADE ADD-ON: This bag lifter assembly is to ease the removal of extractor bags from within the tube.
Purchase Includes: Bag Lifter Assembly, assembly instructions, and an installation video.
This purchase does NOT include one of our technicians doing the installation. If you want a certified technician to complete the install, please call our service department (424.320.0123) to discuss this as a contract for labor and installation.Tools Needed
Wrenches: 9/16″(2x), 5/8″, 1/2″, 1″, crescent
Phillips Screwdriver
Allen Wrenches: 3/16 and 3/32
Side CuttersOther Supplies Needed
Thread Tape
Thread Sealant -
-
-
-
-
-
Containment Vessel with Expeller | #70-3024
$6,000.00This product is for the containment vessel and expeller only.
DOES NOT INCLUDE DRAINDROYD, image of DrainDroyd is for placement purposes only.
Contact us to purchase a DrainDroyd. You can call extraktLAB Sales at (651) 600-0036.
-
Decal Kit, Extractor | #10-1034
$130.00Includes:
ExtraktLab Decal (1)
Fuse Table Decal (1)
Burn Hazard (without Text) (3)
Burn Hazard (with Text) (1)
Emergency Stop Decal (1)
Warning High Voltage (1)
Tested For Electrical Safety (4)
ETL Label Decal (1)
Disconnect Power Before Working Decal (1)
Danger Compressed Gas Decal (1)
High Pressure Vent Before Opening Decals (2)
Foot Crush Warning Decal (1)
Body Crush Warning Decal (1)
Face Shield Decals (3)
Extractor, Collector 1, 2 & 3 (1)
3-Phase Monitor Relay (1)
Safety Gloves (2)
Pinch Point (2)
On/Off Decal (1)
Carbon Dioxide (1)
Open/Close Decal (5)
Prefill Decal (1)
Top Vent Decal (1)
Vent Decals (2)
Bypass Decals (1) -
-
DrainDroyd French Press Lid for Standard Filter Top | #70-3020
$2,100.00The French Press Lid fits the Standard Filter Top and is designed to allow your DrainDroyd to clean exhaust gases and prevent any possible carryover during the venting process. *Requires #70-3010 in order to be used.
Contact us to purchase a DrainDroyd French Press Lid. You can call extraktLAB Sales at (651) 600-0036.
-
DrainDroyd Jacketed Filter Top | #70-3013
$5,250.00The jacketed filter top has a fluid jacket fabricated from stainless steel. Jacket ports are quick disconnect for easy fluid connections. Four ports are provided to provide optional counter current exchange. *Requires #70-3010 in order to be used.
Contact us to purchase a DrainDroyd Jacketed Filter Top. You can call extraktLAB Sales at (651) 600-0036.
-
DrainDroyd Venting Condensor Top | #70-3011
$5,250.00The venting condenser top is designed to allow your DrainDroyd to clean exhaust gases and prevent any possible carryover during the venting process. *Requires #70-3010 in order to be used.
Contact us to purchase a DrainDroyd Venting Condenser Top. You can call extraktLAB Sales at (651) 600-0036.
-
DrainDroyd w/Standard Filter Top & Containment Vessel | #70-3010
$16,500.00DrainDroyd unit with 3,5,10 and 20 micron filters/100 sheets per pack.
Contact us to purchase a DrainDroyd Venting Condenser Top. You can call extraktLAB Sales at (651) 600-0036.
**This item is not available to be purchased online.**
If you attempt to order this product online, your order will NOT be fulfilled. This product listing is for information only. Call extraktLAB Sales at (651) 600-0036.
-
Extractor Bags, 2.5L, 10µm, ID 3″x24″ | #70-1745
$106.00BAG, NYLON 6, 10µm, 3″ ID X 24″ LONG
Can be used for 2.5L or 5L extractor columns.
- FDA approved materials
- Reusable
- 10 Micron Mono-filament
- 24″ Length
- Fits a 3″ Diameter Tube
-
Extractor Bags, 20L, 10µm, ID 6″x20″ | #70-1222
$38.00Used for 20L extractor columns.
- FDA approved materials
- 10 Micron Monofilament
- 20″ Length
- Fits a 6″ Diameter
- 3 of these bags fill one of our 20L extraction columns
- Compatible with some bag filler systems
*This is the extractor bag we recommend for the extraktLAB 140 & extraktLAB 180. If you would rather have a replacement bag of what you originally received, it is #70-1172.
-
Extractor Bags, 20L, 10µm, ID 6″x56″ (10 pack) | #70-1172
$405.00Please Note: This product has a 10-week lead time. We recommend using product #70-1222. Price is for minimum order quantity of 10 bags.
Used for 20L extractor columns.
- FDA approved materials
- 10 Micron Mono-filament
- 56″ Length
- Fits a 6″ Diameter Tube
- Compatible with some bag filler systems
*This bag is a replacement of the bag originally sent with your equipment. We recommend using the shorter bag (#70-1222), which is compatible with some bag filler systems.
-
Extractor Bags, 5L, 10µm, ID 3″x49″ (10 pack) | #70-1221
$210.00Please Note: This product has a 10-week lead time. Price is for minimum order quantity of 10 bags.
Used for 5L extractor columns.
- FDA approved materials
- 10 Micron Monofilament
- 49″ Length
- Fits a 3″ Diameter Tube
- Compatible with some bag filler systems
-
-
Filter Bag, Reusable, 10µm (3 Pack) | #70-1175
$310.00BAG, NYLON 6, 10µm, DRAIN DROYD FILTER
These filter bags are ideal because they are reusable. This is a pack of 3, which is our recommended minimum for each DRAINDROYD, as this allows for one in use, one ready to be used, and one being cleaned. This filter bag is made of monofilament so you won’t have fibers breaking down and being included into your end product.
*Product color is white: Color has been altered to show on white background.
For Reference: 1 Micron = one-millionth of a meter or one-thousandth of a millimeter or thirty-nine millionths of an inch (0.000039)
This filter bag is 10 Micron making it suitable for filtering oils and household dust, but unsuitable for filtering dust mite debris, pet hair/dander, mold spores, bacteria or viruses.The smaller the micron rating, the more can be filtered out but this also means the more your filter will need to be changed. As the filter fills up, the filtering process will slow down.
-
Filter Paper, 20 Micron (100 Pack) | #70-3117
$375.00Technical filter media, 2′ diameter, disposable. 100 sheets per package.
1 Micron = one-millionth of a meter or one-thousandth of a millimeter or thirty-nine millionths of an inch (0.000039)
This filter paper is 20 Micron making it suitable for filtering “large” particles. Large still being smaller than what is visible to the naked eye (~.40 _m)The smaller the micron rating, the more can be filtered out ? but this also means the more your filter will need to be changed. As the filter fills up, the filtering process will slow down.
Produced by United Science.
-
Filter Paper, 3 Micron (100 Pack) |#70-3114
$375.00Disposable, 2′ diameter. 100 sheets per package.
1 Micron = one-millionth of a meter or one-thousandth of a millimeter or thirty-nine millionths of an inch (0.000039)
This filter paper is 3 Micron making it suitable for filtering oils and household dust, but unsuitable for filtering dust mite debris, pet hair/dander, mold spores, bacteria or viruses. Because of the amount being filtered, this filter will “fill up” quickly.The smaller the micron rating, the more can be filtered out ? but this also means the more your filter will need to be changed. As the filter fills up, the filtering process will slow down.
-
Filter, Housing 7″, 10 Micron, Stainless Steel | #80-6184
$385.00Filter for Recycler Filter Housing.
-
FTG Connector, Male, 1/4″T-3/8″, MNPT |#80-2158
$16.00This fitting was typically used to interface between 3/8″ NPT threaded extractor caps and 1/4″ tubing. Most newer 140 models (~2019+) do not require this part (see speedbite fittings). Take care installing this new part. Make sure the threads are started by hand before using a wrench to tighten.
-
-
-
-
-
-
-
-
-
Kit, 110 Critical Spares | #10-1000
$5,747.00Used for 5L Extractor.
Items Included (some parts may also be available separately):
5L Extractor Bag, 3″ x 49″ | #70-1755
3/16″ Check Valve Capsule, HF 300 Pump (4 Pack) | #70-3201
3/8″ Aqueous Seal, HP 300 for SSI Pump (4 Pack) | #70-3202
2 Micron Outlet Filter | #70-3204
BPR Rebuild Kit (Pack of 2) | #80-0004
3K PSI Burst Disc & Holder, Low Pressure | #90-1072
5825 PSI Burst Disc & Holder, High Pressure | #90-1073
LTeflon O-Rings, arge (4 Pack) | #80-0227
Teflon O-Rings, Small (4 Pack) | #80-0229
1/4″ Ball Valve tube Fitting | #80-2310
122 Cast Urethane O-Rings (4 Pack) | #80-46
012 Cast Urethane O-Rings (4 Pack) | #80-46
10K PSI Pressure Regulator | #80-4613
7″ 10 Micron Filter | #80-6184
Extractor Column Tube Top | #80-9121
10A Fuse | #80-6051
Adjustable Compartment Box | #80-9044 -
Kit, 140 Cleaning | #10-1027
$649.00Items Included (also sold separately):
10L Digital Cleaner Ultra Sonicator | #80-4004
Solvent Squirt Bottle | #80-9013
Spatula, High Heat | #80-9015
Spoonula | #80-9016
1″ Tube Brush | #80-9023
1/4″ Tube Brush | #80-9024
7″ Brush | #80-9055
48″L, 1/4″ NPT Thread Brush Rod | #80-9059
1/4″ Thread T-Handle | #80-9060 -
Kit, 140 Critical Spares | #10-1039
$5,651.00Items Included (some parts may also be available separately):
20L Extractor Bag, Large, 56″ | #70-1172
Back Pressure Regulator Rebuild Kit, 10K PSI | #80-0004
Teflon O-Ring, Large | #80-0227
Teflon O-Ring, Small | #80-0229
Ball Valve, 1/4″ Tube Fitting, Certified | #80-2310
122 Cast 90 Duro Clear Urethane O-Rings (4 Pack) | #80-4609
012 Cast U 90 Urethane O-Rings (4 Pack) | #80-4612
10K PSI Pressure Regulator Seal | #80-4613
Top Tubing for E-140 Extractor Column; speedbite | #90-1104
Burst Disc Assembly, 3000 PSI Low Pressure | #90-1072
Burst Disc Assembly, 5825 PSI High Pressure | #90-1073
Adjustable Compartment Box, 3 1/2″ x 13″ | #80-9044 -
Kit, clearSTILL Critical Spares | #10-1057
$3,116.00Items Included (some parts may also be available separately):
Washer, Lock M6, 316SS, Nord-Lock (qty10)| #50-0499
Retaining Ring, External, 15/32 OD Black | #50-0501
Washer, Sealing, Copper M6 | #50-0509
Washer, Sealing, Copper M10 | #50-0514
Washer, Sealing, Copper M8 | #50-0527
Set Screw, 1/4″-20 Thread x 3/16″ long | #50-0566
Wiping Element Holder (qty18) | #70-1382
Rounded Machine Key, .125″x.125″x.75″ | #70-1410
Blade, Wiper Element, Wiped Film (qty9) | #70-1585
Bushing, Wiper Column, 8mm long (qty2) | #70-1586
Bushing, Wiper Column, 16mm long | #70-1587
Ring, Centering, KF25| #70-3029
Ring, Centering, KF40| #80-0394
Ring, Centering, KF16| #80-0403
Gasket, 6″ Tri-Clamp Flanged Viton | #80-0471
Gasket, 2″ Tri-Clamp Flanged Viton | #80-0484
Gasket, DIN 10 Sanitary, Flanged, EPDM | #80-0519
Ring, Centering, KF50, Viton | #80-0557
Ball Bearing, Trade Number 6202, 15mm SH | #80-0562
O-Ring, 5 1/2″ x 5 1/8″ x 3/16″ | #80-0569
O-Ring, 5″ x 4 5/8″ x 3/16″ | #80-0570
Ball Bearing, Trade Number 6201, 12mm SH | #80-0573
O-Ring, 35mm ID x 39mmOD x 2mm, Viton | #80-0605
Gear Pump, Metering 0.6CC/Rev, SS | #80-0717
Seal, Dual Lip Rotary Shaft, 15mm | #80-0736
Cap, Push On, 3/8″ tube x 3/4″, Vinyl PL (qty3) | #80-0737
FTG Bulkhead 3/8″T (qty2)| #80-2168
Cap, 3/8″ Tube (qty6) | #80-2259
Plug, 3/8″ Tube Fitting (qty6) | #80-2260
Plug, 5/16 Tube Fitting (qty6) | #80-2408
Compartment Box, Adjustable 3 1/2″ x 13″ (qty2) | #80-9044
Shaft Key, 1/8″ x 1/8″ x 3/4″, 18-8SS | #80-9525 -
Kit, Ethanol Pump | #10-1015
$20,100.00Items Included:
Priming Syringe
Priming Instructions
2.5 gallon F-Style Polyethylene Tank & Cap
HF 300 SSI Pump
3/8″ Aqueous Seals (2 Pack)
2 Micron Replacement Filter
Transceiver Adapter -
Kit, fracTron Critical Spares | #10-1064
$1,134.00Items Included (some parts may also be available separately):
Gasket, 3/4″ Tri-Clamp Flanged, Viton | #80-0725
Gasket, 1.5″ Tri-Clamp Flanged, Viton | #80-0472
Gasket, 2″ Tri-Clamp Flanged, Viton | #80-0484
Gasket, 4″ Tri-Clamp Flanged, Viton | #80-0486
Gasket, 6″ Tri-Clamp Flanged, Viton | #80-0471
Gasket, 8″ Tri-Clamp Flanged, Viton | #80-0626
O-Ring, 7/8″ OD x 11/16″ ID x 3/32″ W | #80-0524
O-Ring, 19mm ID x 22mm OD x 1.5mm W | #80-0533
O-Ring, 3″ x 3 1/4″, Viton | #80-0659
O-Ring, 9/16″OD x 3/8″ID x 3/32″W | #80-0665
O-Ring, | #80-0821
O-Ring, | #80-0823
O-Ring, | #80-0824
O-Ring, | #80-0825
Spring, Wave | #80-0822
Adjustable Compartment Box, 3 1/2″ x 13″ | #80-9044 -
Kit, Self Flush Seal Wash | #70-3220
$507.00Stainless Steel Self-flush Kit for PR300 Pumps. Self-flush body, inlet and outlet flush check valves, seal, o-ring, and installation instructions. Also contains bushing and plug for conversion to no-flush.
1 self-flush kit per pump; 2 kits required for dual-head pumps.
-
Labels, Printer, igwLAB | #80-6153
$99.001 Roll
Roll of labels for igwLAB printer. (Printer not included.)
For use with:
Printer #80-7024
Barcode Scanner #80-7006 -
-
O-Ring, CO2 Inlet-Filter Housing, Teflon | #80-0411
$253.00Teflon replacement O-rings (2) for extraktLAB’s supercritical CO2 extractor.
-
O-Ring, CO2 Inlet-Filter Housing, Viton | #80-0410
$54.60Viton replacement O-Ring for extraktLAB’s supercritical CO2 extractor.
-
-
O-Rings, 3″, Peroxide Cured (25 Pack) | #80-0221
$41.003″ Peroxcide Cured O-Rings for Extractor and 2.5L and 5L Columns. Quantity of 25.
Peroxide cured O-rings will not provide any false positives on pesticide testing that uses sulfur content to evaluate concentration.
-
-
-
Plastic Syringe | #70-3111
$4.00General purpose syringe for transfer or pump priming (Extrakt 110/110+, Pure 99).
-
Post Heater | #91-1085
$1,100.002000W Heat Rod, 230V
This component is used after the CO2 Recycler to expand the CO2 gas for recirculation into the extractor.
-
Pressure Transducer | #80-0049
$220.00Pressure Transducer used to sense pressures on all extractor models.
-
Printer, igwLAB | #80-7024
$799.00Printer for igwLAB; labels not included.
Sold Separately:
Barcode Scanner #80-7006
Labels #80-6153 -
-
Replacement Wiper for French Press Lid | #70-1182
$160.00Replacement wiper for French Press Lid accessory.
-
Scanner, Barcode, igwLAB | #80-7006
$588.00Barcode Scanner for igwLAB.
Sold Separately:
Printer #80-7024
Labels #80-6153 -
-
Spare Gasket Kit, EPDM | #10-1032
$107.00Spare gasket set for the DrainDroyd Filtration System contains peroxide cured, EPDM gaskets for all lower collection system components.
Contains (also available individually):
2″ Gasket, set of 2 | #80-0281
3″ Gasket | #80-0280
10″ Gasket | #80-0242 -
-
-
Top Tubing for E-140 Extractor Column; Speedbite | #90-1104
$182.00This part contains the assembly connecting the top of the extractor column to the bulkhead on the extractor unit. This is only for late-model 140 units with speedbite fittings on the vessels. Speedbite fittings are gray and do not require thread tape.
-
Union fitting, 1/4″, Swagelok | #80-2109
$17.00This fitting is used for connecting two sections of 1/4″ OD swagelok tubing.
