10L Sonicator (EU Plug) | #80-0826
$629.0010L Ultrasonic Cleaner with EU plug, 50Hz
No products in the cart.
Showing all 24 results
10K PSI BPR used in extraktLAB’s E-110, E-140, E-180 & pure99.
This is an UPGRADE ADD-ON: This bag lifter assembly is to ease the removal of extractor bags from within the tube.
Purchase Includes: Bag Lifter Assembly, assembly instructions, and an installation video.
This purchase does NOT include one of our technicians doing the installation. If you want a certified technician to complete the install, please call our service department (424.320.0123) to discuss this as a contract for labor and installation.
Tools Needed
Wrenches: 9/16″(2x), 5/8″, 1/2″, 1″, crescent
Phillips Screwdriver
Allen Wrenches: 3/16 and 3/32
Side Cutters
Other Supplies Needed
Thread Tape
Thread Sealant
CO2 connection kit allows up to 6 CO2 tanks to be used in conjunction to feed a 110 or 140 extractor. This manifold is also expandable, allowing a user to customize their CO2 delivery system.
Includes:
ExtraktLab Decal (1)
Fuse Table Decal (1)
Burn Hazard (without Text) (3)
Burn Hazard (with Text) (1)
Emergency Stop Decal (1)
Warning High Voltage (1)
Tested For Electrical Safety (4)
ETL Label Decal (1)
Disconnect Power Before Working Decal (1)
Danger Compressed Gas Decal (1)
High Pressure Vent Before Opening Decals (2)
Foot Crush Warning Decal (1)
Body Crush Warning Decal (1)
Face Shield Decals (3)
Extractor, Collector 1, 2 & 3 (1)
3-Phase Monitor Relay (1)
Safety Gloves (2)
Pinch Point (2)
On/Off Decal (1)
Carbon Dioxide (1)
Open/Close Decal (5)
Prefill Decal (1)
Top Vent Decal (1)
Vent Decals (2)
Bypass Decals (1)
Filter for Recycler Filter Housing.
This fitting was typically used to interface between 3/8″ NPT threaded extractor caps and 1/4″ tubing. Most newer 140 models (~2019+) do not require this part (see speedbite fittings). Take care installing this new part. Make sure the threads are started by hand before using a wrench to tighten.
Items Included (also sold separately):
10L Digital Cleaner Ultra Sonicator | #80-4004
Solvent Squirt Bottle | #80-9013
Spatula, High Heat | #80-9015
Spoonula | #80-9016
1″ Tube Brush | #80-9023
1/4″ Tube Brush | #80-9024
7″ Brush | #80-9055
48″L, 1/4″ NPT Thread Brush Rod | #80-9059
1/4″ Thread T-Handle | #80-9060
Items Included (some parts may also be available separately):
20L Extractor Bag, Large, 56″ | #70-1172
Back Pressure Regulator Rebuild Kit, 10K PSI | #80-0004
Teflon O-Ring, Large | #80-0227
Teflon O-Ring, Small | #80-0229
Ball Valve, 1/4″ Tube Fitting, Certified | #80-2310
122 Cast 90 Duro Clear Urethane O-Rings (4 Pack) | #80-4609
012 Cast U 90 Urethane O-Rings (4 Pack) | #80-4612
10K PSI Pressure Regulator Seal | #80-4613
Top Tubing for E-140 Extractor Column; speedbite | #90-1104
Burst Disc Assembly, 3000 PSI Low Pressure | #90-1072
Burst Disc Assembly, 5825 PSI High Pressure | #90-1073
Adjustable Compartment Box, 3 1/2″ x 13″ | #80-9044
Items Included (also available individually):
Face Shield | #80-0059
Headgear | #80-0137
Pressure Transducer used to sense pressures on all extractor models.
This part contains the assembly connecting the top of the extractor column to the bulkhead on the extractor unit. This is only for late-model 140 units with speedbite fittings on the vessels. Speedbite fittings are gray and do not require thread tape.
This fitting is used for connecting two sections of 1/4″ OD swagelok tubing.